Freud 10” x 40T Premier Fusion vs. Freud Diablo 10″ x 60T

Looking for a new table saw blade? Compare the benefits of the Freud 10” x 40T Premier Fusion and Freud Diablo 10″ x 60T and make a smart purchase!

Lets compare these two Freud table saw blades: the Freud 10” x 40T Premier Fusion and the Freud Diablo 10” x 60T.

Freud 10” x 40T Premier Fusion
Freud Diablo 10” x 60T

Features & Benefits

You can read our complete guide to buying a table saw blade.

Related: Choosing the Right Table Saw Blade

Weve also got a roundup of the best 10” table saw blades.

Size

Both saw blades have a 10 diameter and fit on a 5/8 diameter arbor. Typical table saws have a 5/8arbor and can accept blades up to 10in diameter. Thus, both table saw blades should be generally usable on many saws.

The 10x 40T Premier Fusion has a plate thickness of 0.098 and cuts a 1/8 (full) kerf. The Diablo 10x 60T is 0.071 thick and cuts a 0.098 (thin) kerf. (The termkerfis the width of the cut that the blade leaves in the material being cut.)

A 1/8kerf is considered afullkerf and will work on most table saws. On saws with less power, a full-kerf blade could cause the saw to have trouble with thicker or harder material, when compared with a thin-kerf blade.

A kerf less than 1/8is referred to as athinkerf. Thin kerfs waste less material than full-kerf blades and make it easier for saws to cut through thick or hard wood. Most, but not all, table saws can accept thin-kerf blades. Make sure your riving knife is thinner than the kerf, or dangerous binding can take place.

Teeth

Both products have TiCo high-density carbide teeth in a Hi-ATB configuration. The 10x 40T Premier Fusion has 40 teeth. The Diablo 10x 60T has 60 teeth.

Blades having between 40 and 60 teeth are typically viewed as general-purpose blades. They can perform ripping as well as crosscutting, but not as well as a blade specifically made for such cuts.

Alternate top bevel (ATB) teeth are cut on a bevel instead of being straight across. This design lets them slice through wood instead of tearing out chunks, for smoother crosscuts. They do have a tendency to be less durable than flat-top teeth. Hi-ATB teeth have a steeper bevel angle than regular ATB teeth, and perform even better on materials like plywood and melamine.

Pros & Cons

Lets take a look at some of the pluses and minuses of these products.

For the 10x 40T Premier Fusion:

Pros

  • Glassy-smooth cross cuts on many kinds of wood
  • Very little tear-out cutting plywood
  • Smooth enough results for gluing without sanding
  • Long useful life before needing sharpening
  • Less dust than comparable blades

Cons

  • Some customers report teeth chipped either out of the box or after only a few cuts
  • Does not rip as well as some other general-purpose blades, especially hardwoods
  • Hard to get sharpened locally, may need to send to factory
  • The red coating may rub off on harder materials

For the Diablo 10” x 60T:

Pros

  • Minimal tear-out on cuts
  • Thin kerf lets lower-powered saws handle more challenging workpieces
  • Relatively quiet operation
  • Little to no burning of wood

Cons

  • Not as clean of cuts as 80-tooth blades will provide
  • Thin kerf leads to some flexing; may not cut quite as straight as full-kerf blades

Comparison Chart

Below is a full side-by-side look at these products’ specs. You can view comparisons of the Freud 10” x 40T Premier Fusion with other products

and comparisons of the Freud Diablo 10” x 60T with other products.

Freud 10” x 40T Premier FusionFreud Diablo 10” x 60T
Freud 10” x 40T Premier Fusion
Freud Diablo 10” x 60T
BrandFreudFreud
Blade Diameter10”10”
Arbor Size5/8”5/8”
Thickness0.098”0.071”
Kerf1/8”0.098”
Tooth Bevel30°
Tooth Count4060
Tooth ConfigHi-ATBHi-ATB
Tooth MaterialTiCo high-density carbideTiCo high-density carbide
Rake18°15°
Expansion Slots
Pros
  • Glassy-smooth cross cuts on many kinds of wood
  • Very little tear-out cutting plywood
  • Smooth enough results for gluing without sanding
  • Long useful life before needing sharpening
  • Less dust than comparable blades
  • Minimal tear-out on cuts
  • Thin kerf lets lower-powered saws handle more challenging workpieces
  • Relatively quiet operation
  • Little to no burning of wood
Cons
  • Some customers report teeth chipped either out of the box or after only a few cuts
  • Does not rip as well as some other general-purpose blades, especially hardwoods
  • Hard to get sharpened locally, may need to send to factory
  • The red coating may rub off on harder materials
  • Not as clean of cuts as 80-tooth blades will provide
  • Thin kerf leads to some flexing; may not cut quite as straight as full-kerf blades
We use cookies and other tracking technologies to analyze our website traffic, to understand where our visitors are coming from, and to improve your browsing experience on our website.
As an Amazon Associate, I earn from qualifying purchases.