DeWalt 10” x 40T PrecisionTrim vs. Freud 10” x 40T Premier Fusion

Thinking about a new table saw blade? Compare the benefits of the DeWalt 10” x 40T PrecisionTrim and Freud 10” x 40T Premier Fusion and make an informed purchase!

Lets take a look at these two table saw blades: the DeWalt 10” x 40T PrecisionTrim and the Freud 10” x 40T Premier Fusion.

DeWalt 10” x 40T PrecisionTrim
Freud 10” x 40T Premier Fusion

Features & Benefits

You can read more in our complete guide to buying a table saw blade.

Related: Choosing the Right Table Saw Blade

Weve also got a roundup of the best 10” table saw blades.

Size

Both saw blades have a 10 diameter and have a 5/8 arbor hole. Most table saws have a 5/8arbor and can handle blades up to 10in diameter. This means that both products will be widely usable on a range of saws.

The 10 x 40T PrecisionTrim has a 0.098 (thin) kerf. The 10x 40T Premier Fusion is 0.098 thick and has a 1/8 (full) kerf. (The termkerfmeans the width of the cut that the blade makes in the material being cut.)

A 1/8kerf is considered afullkerf and ought to work with most table saws. On lower-powered saws, a full-kerf blade can cause the saw to struggle with thicker or harder material, compared with a thin-kerf blade.

A kerf less than 1/8is known as athinkerf. Thin kerfs waste less material than full-kerf blades and make it easier for saws to cut through thick or hard material. Most, but not all, table saws can take thin-kerf blades. Make sure your riving knife is thinner than the kerf, or dangerous binding can occur.

Teeth

Both table saw blades have 40 teeth. The 10 x 40T PrecisionTrim has C4 carbide teeth in an ATB configuration. The 10x 40T Premier Fusion has TiCo high-density carbide teeth in a Hi-ATB configuration.

Blades with 40-60 teeth are typically considered general-purpose blades. They can perform both rip cuts and crosscuts, but not as well as a blade purpose-made for those cuts.

Alternate top bevel (ATB) teeth have a bevel shape rather than being flat across. This shape lets them slice through wood as opposed to tearing out chunks, resulting in crosscuts with less tear-out. They do tend to be less durable than flat-top teeth. Hi-ATB teeth are beveled at a steeper angle than regular ATB teeth, and do an even better job on materials like plywood and melamine.

Pros & Cons

Lets take a look at some of the pluses and minuses of these products.

For the DeWalt:

Pros

  • Thick C4 carbide teeth with a precision finish
  • Very clean crosscuts
  • Good performance ripping hardwood and cutting plywood
  • More durable than blades with higher ATB tooth angle
  • Quiet when cutting, not much louder than when spinning
  • No chip-out when cutting material like melamine

Cons

  • Teeth are somewhat brittle and can be damaged if hitting nails or if used on metal
  • Some customers received blades with a noticeable warp or wobble

For the Freud:

Pros

  • Glassy-smooth cross cuts on many kinds of wood
  • Very little tear-out cutting plywood
  • Smooth enough results for gluing without sanding
  • Long useful life before needing sharpening
  • Less dust than comparable blades

Cons

  • Some customers report teeth chipped either out of the box or after only a few cuts
  • Does not rip as well as some other general-purpose blades, especially hardwoods
  • Hard to get sharpened locally, may need to send to factory
  • The red coating may rub off on harder materials

Comparison Chart

Below is a full side-by-side comparison of these products’ specs. You can view comparisons of the DeWalt 10” x 40T PrecisionTrim with other products

and comparisons of the Freud 10” x 40T Premier Fusion with other products.

DeWalt 10” x 40T PrecisionTrimFreud 10” x 40T Premier Fusion
DeWalt 10” x 40T PrecisionTrim
Freud 10” x 40T Premier Fusion
BrandDeWaltFreud
Blade Diameter10”10”
Arbor Size5/8”5/8”
Thickness0.098”
Kerf0.098”1/8”
Tooth Bevel30°
Tooth Count4040
Tooth ConfigATBHi-ATB
Tooth MaterialC4 carbideTiCo high-density carbide
Rake18°
Expansion Slots
Pros
  • Thick C4 carbide teeth with a precision finish
  • Very clean crosscuts
  • Good performance ripping hardwood and cutting plywood
  • More durable than blades with higher ATB tooth angle
  • Quiet when cutting, not much louder than when spinning
  • No chip-out when cutting material like melamine
  • Glassy-smooth cross cuts on many kinds of wood
  • Very little tear-out cutting plywood
  • Smooth enough results for gluing without sanding
  • Long useful life before needing sharpening
  • Less dust than comparable blades
Cons
  • Teeth are somewhat brittle and can be damaged if hitting nails or if used on metal
  • Some customers received blades with a noticeable warp or wobble
  • Some customers report teeth chipped either out of the box or after only a few cuts
  • Does not rip as well as some other general-purpose blades, especially hardwoods
  • Hard to get sharpened locally, may need to send to factory
  • The red coating may rub off on harder materials
We use cookies and other tracking technologies to analyze our website traffic, to understand where our visitors are coming from, and to improve your browsing experience on our website.
As an Amazon Associate, I earn from qualifying purchases.